Sorry, this product is not available to purchase.
- Estimated life of 91.3 years based on 3 hours use per day
Lighting Facts Per Bulb
|Brightness 6249 lumens|
Estimated Yearly Energy Cost $5.42
Based on 3 hrs/day, 11¢/kWh
Cost depends on rates and use
Based on 3 hrs/day91.3 years
|Energy Used45 watts|
Maxlite's LED Vapor Tight fixture features a one piece white (PC) polycarbonate body and a full length polycarbonate lens. Designed to meet or exceed IES recommended Fc at installed heights for parking drive lane compliance. Ideal for utility lighting, parking garages, stairwell lighting, car washes and any place where water may get into a fixture.
- Non-corrosive one piece (PC) polycarbonate housing
- Translucent white lens
- Stainless steel spec grade hasps and clips
- Back KO location and end sealed conduit openings
- Class II LED driver
- Surface or suspended mounting
- IP65 rated with hermetic sealing
- 0-10V dimming. Compatible with Lutron NTSTV-DV-WH and DVSTV-WH dimmers
- DLC listed
- NSF certified
- 10 year limited warranty with labor allowance
- Product must be rated for the application; operated ≤ 16 hours per day; in ambient -22°F to 113°F
- Labor Allowance - Up to $25 per unit; labor allowance up to $500 per unit available for an additional purchase. Contact a Bulbs.com Lighting Specialist for details
- It is not a requirement to register the warranty to receive warranty coverage, but you must register the warranty if you want to be eligible to receive the labor allowance associated with the 10 year limited warranty
A rating, expressed in watts, to indicate the rate at which a lamp consumes energy. Also known as wattage value.
The total wattage of fluorescent lamps in a fixture that this fixture replaces.
Color Rendering Index is an international system used to rate a lamp's ability to render object colors. The higher the CRI (based upon a 0-100 scale) the richer and more accurately colors generally appear. CRI differences among lamps are not usually visible to the eye unless the difference is more than 3-5 points.
|Color Temperature (Kelvin)
Color Temperature (Kelvin)
An expression of the hue of the light emitted, measured in degrees Kelvin. Usually expressed by a four digit number followed by (k), such as 2700k. Higher temperatures indicate whiter, "cooler" colors, while lower temperatures indicate yellower, "warmer" colors. Some common Kelvin temperature benchmarks are 2700k (warm white), 3500k (neutral white), 4100k (cool white), 5000k (bright white), and 6500k (daylight).
A rating of the initial light output of a bulb, rated after 100 hrs of operation. Lumens are a measure of how much light falls on one square foot of area, one foot away from the light source.
|Average Rated Life (hr)
Average Rated Life (hr)
A measurement of the average length of time, between first use and the point when 50% of the lamps tested have stopped functioning, , using an operating cycle of 3 hours on, 20 minutes off.
|Operating Temperature (°F)
Operating Temperature (°F)
The ambient temperature in which the product can safely operate.
|-22 to 113
|Bulb Type Supplied
Bulb Type Supplied
Type of bulb supplied with the fixture
Also referred to as "Maximum Overall Length" (MOL). For light bulbs, it measures the length of a light bulb, from the top of the bulb to the bottom of the base or pins and is typically expressed in inches. For light fixtures and ballasts, it applies to the total horizontal length of the item.
For fixtures and ballasts, width is the measurement of the total horizontal distance from left to right of the product in inches.
For ballasts and fixtures, height is the measurement of total vertical distance from the top of the product to the bottom expressed in inches.
The decorative finish of the item.
|Surface or suspended
|10 year limited
Suitable for exterior or interior location in which uncontrolled liquid may drip, splash or flow on or against electrical equipment.
Approved by the DesignLights Consortium, a collaboration of utility companies and regional energy efficiency organizations. Approved products meet the consortium's standards for ensuring high-quality, energy-efficient lighting design. There are two levels, Standard and Premium
Code identifying the product in DLC (DesignLights Consortium) listings.
|Food Equipment Certification
Food Equipment Certification
The NSF (National Science Foundation) establishes minimum food protection and sanitation requirements for the materials, design, fabrication, construction and performance of food handling and processing equipment. The ETL (Edison Testing Laboratories) Mark is proof of product compliance to North American safety standards.
Indicates whether a bulb can be dimmed in conjunction with a suitable dimmer control.
Recommended With This Product